SCO OpenServer Handbook
Index
I
-
IBM, external floppy, support
-
IBM437 character set,
``Creating a character mapping table'',
``Creating a character mapping table''
-
icons
-
iconv(C)
-
ID number, SCSI tape drive,
``Problems with SCSI tape drives'',
``Problems with SCSI tape drives''
-
IDE, CD-ROM, specifying
-
IDE
-
IDE CD-ROM
-
idmkenv(ADM)
-
ifor_pmd.pid
-
initialization letters
-
init(M)
-
INITSH: /etc/bcheckrc not found
-
inittab. See
/etc/inittab
-
inodes
-
installation
-
adding hard disks,
``Adding secondary hard disks'',
``Installing a hard disk'',
``The installation and upgrade procedure'',
``BIOS support for disks larger than 1024 cylinders''
-
adding users
-
additional software
-
bitpads
-
BTLDs
-
bus cards,
``Adding serial and parallel ports'',
``Installing bus cards'',
``Adding and configuring SCO-supported serial cards'',
``Adding and configuring parallel ports''
-
cable connections
-
CD-ROM drives
-
checklist for SCO systems
-
COM ports
-
configuring devices during
-
configuring mail system
-
configuring networks
-
creating backup
-
Customize option
-
emergency boot floppy disk set
-
floptical drives
-
init,
``The installation and upgrade procedure'',
``The installation and upgrade procedure''
-
Interactive option
-
Internet services components
-
memory
-
modems,
``Installing serial terminals'',
``Adding modems'',
``Smartmodem 2400, V-series 9600 or compatible''
-
monochrome cards
-
mouse,
``Configuring a mouse'',
``Configuring a mouse'',
``Configuring a mouse'',
``Configuring a mouse'',
``Adding mice and bitpads'',
``Installation and upgrade checklist''
-
multiport cards,
``Adding and configuring SCO-supported serial cards'',
``Adding and configuring SCO-supported serial cards'',
``Adding serial and parallel ports''
-
multiuser mode
-
Netscape Web server
-
network card
-
on EISA systems
-
over the network,
``Installing software'',
``Installing software''
-
planning system
-
Plug and Play devices
-
printers
-
problems,
``System does not boot during installation'',
``System does not boot during installation'',
``Solving problems during installation'',
``Error reading a floppy disk'',
``System reboots from Boot Disk or screen blanks after Boot: prompt'',
``Errors when using SCSI installation devices'',
``System hangs at hardware configuration screen'',
``System does not boot during installation''
-
responding to prompts
-
restarting
-
root password
-
SCO systems,
``The installation and upgrade procedure'',
``Installing or upgrading an SCO system''
-
single-user mode
-
software,
``Installing software'',
``Loading software''
-
starting Desktop
-
stopping
-
superuser password
-
tape drives
-
terminals
-
troubleshooting
-
types
-
UNIX partition on DOS
-
upgrading
-
upgrading SCO systems
-
Use whole disk for UNIX
-
installed software
-
installpkg(ADM), installing BTLDs
-
instbb(ADM)
-
INT signal
-
intelligent serial adapter
-
intent logging
-
Interactive disk setup
-
interleave for hard disks
-
internal memory, adding
-
internal modems,
``Choosing which serial port to use'',
``Guidelines for non-supported modems''
-
internal system codeset,
``Setting the internal system codeset'',
``Device mapping''
-
International Settings Manager
-
Internet
-
Internet Manager
-
Internet Service Provider
-
Internet services, installing components
-
interrupt key,
``The keyboard'',
``The keyboard''
-
interrupt trigger level, changing
-
interrupt vectors
-
invoking programs, users
-
IP address, server, Netscape default
-
IPCCT_pipe
-
ir: ERROR: Tape controller ... not found, message
-
IRQ (physical interrupt). See
interrupt vectors
-
Irwin
-
ISA PnP Configuration Manager
-
ISO 9660, CD-ROM format
-
ISO8859-1 character set,
``About locales'',
``Setting the internal system codeset'',
``Creating a character mapping table'',
``Creating a character mapping table'',
``About locales''
-
ISO8859-1 character set
-
ISO8859-15 character set
-
ISP